Notice: Do not load an earlier version over a later version of the software.
Version 3.42 Released 3/3/2016
Update: Address a voltage flicker issue and fixes an issue with failing starter disconnect on 24V Yanmar marine models.
Version 3.32
Correction: Lose of random numbers on hourmeter.
Version 3.31
Not Released
Version 3.30
Not Released
Version 3.29
Not Released
Version 3.28
General Motors Tier 3: Loss of ECM corrected.
Version 3.27
General Motors Tier 3: Support Added.
Version 3.26
Not Released
Version 3.25
Not Released
Version 3.24
General Motors 1.6L: Change to Low Oil Level fault.
Version 3.23
Configuration Settings: Lose of settings corrected.
Version 3.22
Communication Errors: Change to ECM message handling during remote start sequence to avoid nuisance fault.
Version 3.21
Parameter Changes: Factory defaults of "Cn" and "CO" settings linked to Ec and Uc parameters.
Version 3.20
LOC Fault: Revision made to address fault condition when (1) coolant sensor not used
(2) upon low battery voltage condition. Also during shutdown (ECD/EFCD models only).
Parameter Change (Marine ECD/EFCD): Add Cn08 and Cn09 for 1-hr. power following generator operation.
Parameter Change: Separate Ec62 fault code created for sea water pump fault.
Version 3.15 thru 3.19
Not released on production units.
Version 3.14
J1939 Address: Add parameter (CA) to support J1939 "1" address. Refer to TT-1364.
Version 3.13
Voltage Regulation: Modifications for new applications.
Low Oil Pressure Shutdown: Added support for DC controller (RESL residential gensets).
Version 3.12 (All Advanced Digital Control controllers, except residential ADC-RES and DC-RET)
Parameter Resets: Removed automatic reset of CA parameter when Ec or CN parameters changed
Cn06 Selection: Change to allow one-hour power
Remote Digital Gauge: Added support of gauge
Version 3.11 (All Advanced Digital Control products, except ADC-RES for Residential)
Parameter Ec/Uc: Removed automatic link when single parameter changed
Parameter Update: Automatic realtime updates to battery voltage, AC voltage, frequency, and engine temp.
Version 3.10 (All Advanced Digital Control products, except new ADC-RES for Residential
Merge: Versions 1.xx and Version 2.xx with single software version.
Version 3.00 (Marine Only: 10-15EGD and 9-15EGZD)
Original production release for generator models indicated.
2" Digital Gauge Kit (GM50822-KP1): Must use this version when used with 10-15EGD and 9-15EGZD generator models.
Version 2.20 (Marine Only: 5/7.3 ECD and 4/6EFCD)
2" Digital Gauge (GM50822-KP1): Must use this version when used with 5/7.3ECD and 4/6EFCD.
Version 1.27
Fault reset: Fault is no longer reset when remote start/stop contact open. Revised for standby applications including 8.5, 12, 15, 30 RES(L) and 15, 30 RYG.
Version 1.26
Digital Control (DC): Added fault conditions for overvoltage, undervoltage, and overcrank (locked rotor condition).
GM Engines: Changed to 450 RPM crank disconnect and 60 sec. underfrequency fault condition.
Version 1.25
Not released on production units.
Version 1.24
Voltage Settings: Stability settings changed for Marine EOZD (60 Hz) generators.
Version 1.23
Engine Type Ec09: Adjustment for brushless alternator applications.
Version 1.22
Voltage Output: Parameter adjustment to maintain 240 VAC out on DC 2200 (residential).
Version 2.11 (Marine Only: 5/7.3 ECD and 4/6EFCD)
Display enhancements: Add fault event log access and operation data (voltage, frequency, oil pressure, engine temperature, and battery voltage).
Version 2.10 (Marine Only: 5/7.3 ECD and 4/6EFCD)
Original release for generator models indicated.
Version 1.21
Configuration Parameters (Cn): Added Cn06 selection for 1-hour display activation following generator operation and using Remote Digital Gauge. Cn01 allows for continuous power for displays when using both ADC 2100 and Remote Digital Gauge.
Version 1.20
Configuration Parameters (Uu): Expanded Uu selections to support voltage data represented on Remote Digital Gauge.
Version 1.19
Not released on production units.
Version 1.18
P7 Jumper: Replaced with continuous power enabled when (1) Remote ADC Gauge via CANbus J1939 used and (2) master switch is on OFF or AUTO position.
Locked Rotor: Indicated as Overcrank Shutdown during crank cycle when low output voltage condition exists.
Version 1.17
Fuel Pump: Added capability to prime the fuel pump. Changed high engine temperature shutdown to 240 deg F.
Version 1.15
Loss of Coolant Shutdown: Inhibit time changed to 10 seconds.
Version 1.14
ADC Remote Gauge: Modify remote STOP/START command from gauge and modify AC voltage display on gauge.
Default parameters: Revision to parameter value range and default reset.
Version 1.13
Master Switch: Flashing relay synchronization.
Version 1.12
Halon System: 3-second time delay added (marine only) after crank disconnect to prevent start-up disruption due to auxiliary fault.
High Engine Temperature: Fault value increased to 350 deg. F for models 8.5 and 12 RES.
Version 1.11
Low Oil Pressure Shutdown: Added support for Remote ADC Gauge (Marine).
Version 1.09
Voltage Stability: Improved stability at changing loads.
Version 1.09
Voltage Stability: Improved stability at certain loads.
Version 1.08
Remote Gauge: Revised support of ADC Remote Gauge to address remote start shutdown on over-voltage.
Version 1.07
Revision not released on production units.
Version 1.06
Revision not released on production units.
Version 1.05
Revision not released on production units.
Version 1.04
Improve governor stability.
Version 1.03
Initial Release